Knowing Plumbing Basics is Important When Installing a Bathtub
Knowing Plumbing Basics is Important When Installing a Bathtub
Blog Article
Each person seems to have his or her own rationale involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, however it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is also a reasonably tough task. If the old tub is readily obtainable, the project can relocate easily; if you have to open a wall surface to eliminate the old tub as well as position the brand-new tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will need a helper to leave the old bathtub as well as set in the brand-new one. Ensure you have qualified yourself for the work and also fit attempting it. Rather than working with a professional to take control of a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly assist you install a new bath tub in your restroom if you have already purchased a new tub and do not require to change the arrangement of your previous water pipelines.
Your tools as well as product checklist should consist of the following:
Getting ready for the Installation
To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, position the tub in the required setting. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub until the spirit level reviews level.
To install taps, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Switch on the water as well as inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Fill the bathtub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait until the bathtub has been utilized at least when as this will certainly settle it right into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Secure the faucet in place with the supplier provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, leading to problems with moisture and feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in use. The sealant can crack relatively very early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the market. It is advisable to fit the floor tiles using water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog entry on How to Install a Bathtub when doing a lookup on the internet. Remember to take the time to promote this article if you appreciated it. Thanks for your time invested reading it.
Secure your home, ring now. Report this page